• PCB Supplies Product Slider

    Drilling Bits
    End Mills
    Routers
    Rings

    Chemicals

    PCB Materials

    Health and Safety

  • Drill Size Chart

    This drill size chart provides a list of standard size drill bits in several measurement systems, including fractional, metric, wire gauge number, and letter. The decimal equivalents of the diameters are shown in both English and Metric units. Fractional sizes are measured in inches, while metric sizes are measured in millimeters. The wire gauge and letter systems refer to tool diameters that increase as the wire gauge decreases from #107 to #1 and then continues from A to Z.


    Drill Size Chart
    Drill size
    Diameter (in) Diameter (mm)
    0.05 mm 0.0020 0.0500
    #106 0.0023 0.0584
    #105 0.0027 0.0686
    #104 0.0031 0.0787
    #103 0.0035 0.0889
    #102 0.0039 0.0991
    0.1 mm 0.0039 0.1000
    #101 0.0043 0.1092
    #100 0.0047 0.1194
    #99 0.0051 0.1295
    #98 0.0055 0.1397
    #97 0.0059 0.1499
    #96 0.0063 0.1600
    #95 0.0067 0.1702
    #94 0.0071 0.1803
    #93 0.0075 0.1905
    0.2 mm 0.0079 0.2000
    #92 0.0079 0.2007
    #91 0.0083 0.2108
    #90 0.0087 0.2210
    #89 0.0091 0.2311
    #88 0.0095 0.2413
    #87 0.0100 0.2540
    #86 0.0105 0.2667
    #85 0.0110 0.2794
    #84 0.0115 0.2921
    0.3 mm 0.0118 0.3000
    #83 0.0120 0.3048
    #82 0.0125 0.3175
    #81 0.0130 0.3302
    #80 0.0135 0.3429
    #79 0.0145 0.3680
    0.4 mm 0.0158 0.4000
    #78 0.0160 0.4064
    #77 0.0180 0.4572
    0.5 mm 0.0197 0.5000
    #76 0.0200 0.5080
    #75 0.0210 0.5334
    #74 0.0225 0.5715
    0.6 mm 0.0236 0.6000
    #73 0.0240 0.6096
    #72 0.0250 0.6350
    #71 0.0260 0.6604
    0.7 mm 0.0276 0.7000
    #70 0.0280 0.7112
    #69 0.0292 0.7417
    #68 0.0310 0.7874
    0.8 mm 0.0315 0.8000
    #67 0.0320 0.8128
    #66 0.0330 0.8382
    #65 0.0350 0.8890
    0.9 mm 0.0354 0.9000
    #64 0.0360 0.9144
    #63 0.0370 0.9398
    #62 0.0380 0.9652
    #61 0.0390 0.9906
    1 mm 0.0394 1.0000
    #60 0.0400 1.0160
    #59 0.0410 1.0414
    #58 0.0420 1.0668
    #57 0.0430 1.0922
    1.1 mm 0.0433 1.1000
    #56 0.0465 1.1811
    1.2 mm 0.0472 1.2000
    1.3 mm 0.0512 1.3000
    #55 0.0520 1.3208
    #54 0.0550 1.3970
    1.4 mm 0.0551 1.4000
    1.5 mm 0.0591 1.5000
    #53 0.0595 1.5113
    1.6 mm 0.0630 1.6000
    #52 0.0635 1.6129
    1.7 mm 0.0669 1.7000
    #51 0.0670 1.7018
    #50 0.0700 1.7780
    1.8 mm 0.0709 1.8000
    #49 0.0730 1.8542
    1.9 mm 0.0748 1.9000
    #48 0.0760 1.9304
    #47 0.0785 1.9939
    2 mm 0.0787 2.0000
    #46 0.0810 2.0574
    #45 0.0820 2.0828
    2.1 mm 0.0827 2.1000
    #44 0.0860 2.1844
    2.2 mm 0.0866 2.2000
    #43 0.0890 2.2606
    2.3 mm 0.0906 2.3000
    #42 0.0935 2.3749
    2.4 mm 0.0945 2.4000
    #41 0.0960 2.4384
    #40 0.0980 2.4892
    2.5 mm 0.0984 2.5000
    #39 0.0995 2.5273
    #38 0.1015 2.5781
    2.6 mm 0.1024 2.6000
    #37 0.1040 2.6416
    2.7 mm 0.1063 2.7000
    #36 0.1065 2.7051
    #35 0.1100 2.7940
    2.8 mm 0.1102 2.8000
    #34 0.1110 2.8194
    #33 0.1130 2.8702
    2.9 mm 0.1142 2.9000
    #32 0.1160 2.9464
    3 mm 0.1181 3.0000
    #31 0.1200 3.0480
    3.1 mm 0.1221 3.1000
  • Welcome Unregistered

    • If this is your first visit, and you are not registered already, please click the register link below to proceed. Register